Wesley PCT-3510-6SA ST Manual de usuario descargar pdf (Pagina 14)

Owner’s Manual and Service Guide – PC & PCT Series 14

WARNING

NOTE

OPERATING INSTRUCTIONS

8 – Go out of Menu 1. Press CE. Press CE again to Log Off

the Supervisor Mode.

9 – Check out the new Supervisor PIN. Press 0 0 5 4 3 2 1

ENTER. You should be in Supervisor Mode. You can now go

to any menu by pressing the menu number and ENTER.

Remember: This is an example. You should change your

Supervisor PIN to one known only to you.

10 – Determine Last user. While in Supervisor Mode press 3

ENTER. This places you in the Last User Menu as indicated

by three red LED flashes. Press ENTER again. The LED

flashes will indicate the last user. The Green LED is for the

10’s digit. The Red LED is for the 1’s digit. Example 1: A

single Red LED flash indicates User 01 last operated the

vehicle. Example 2: Two Green flashes and three Red

flashes would indicate User 23 last operated the vehicle.

Press CE to leave the menu.

11 – Enable or Disable Maintenance Alarm. Press 4 ENTER.

There will be four red LED flashes. Press ENTER again. If

the Green LED flashes, the alarm is enabled. Press ENTER

again and the Red LED will flash showing the alarm to be

disabled. Press ENTER again and the Green LED will flash

showing the alarm to be again enabled.

12 – Listen to the maintenance alarm. While in Menu 4 press

1 ENTER. The maintenance alarm will sound. Press CE to

leave the menu. Press CE again to Log Off the Supervisor

Mode.

Note: If the switch is left unattended in Supervisor mode, it

will automatically exit the mode after approximately one

minute.

13 – If you are unable to get into the Supervisor mode after

trying either the default PIN or a newly assigned PIN, go

back to Step 1 and reset the switch.

If all else fails or if you have questions about programming or

installing the SAFE-T-LOCK, call Tech Support at 1-800-

241-2869.

Directional Switch: The directional rocker or toggle switch

is used to place the vehicle in one of three operating modes

– forward, reverse, or neutral. (Figure 6) shows a rocker

directional switch.

The directional switch MUST be in

NEUTRAL (center) position BEFORE

selecting vehicle “ON” or a “Static Return

to Off” (SRO) error code will be generated by the motor

controller. The vehicle is temporarily immobilized as a

standard safety feature. (If your vehicle is equipped with the

Optional Foot Presence Switch and the unit is already turned

on and in neutral position, the foot presence switch MUST

be engaged before the directional switch is placed in forward

or reverse mode, or the same error code will be displayed

and the vehicle temporarily immobilized.) If this error code is

displayed, return the directional switch to the neutral

position, ensure the foot presence switch is engaged, and

then switch the directional Switch to the desired forward or

reverse position and the vehicle will operate.

FIGURE 6

To prevent unexpected vehicle

movement when the vehicle is

next driven, always place the

directional switch in the

NEUTRAL position when

leaving the vehicle.

Battery Discharge Indicator (BDI): The battery discharge

indicator, (Figure 7), communicates directly with the onboard

controller and provides information on various system

parameters, such as battery state-of-charge, operating hours

(on some models), or maintenance status including error

codes.

FIGURE 7

When powering on the vehicle, the BDI first indicates the

hours (Note: The controller is programmed to indicated

traction hours, which is the time that the motor is engaged

and the vehicle is moving. The controller can be

programmed to display “key-on” hours which records time

that the key switch is in the on position, regardless of

whether it is moving or not). It then cycles through to the

state of battery charge, measured in percent charge

remaining. If there are any faults recorded by the controller,

the BDI will display an error code and the LED by the tool

wrench symbol will illuminate.

Directional Switch

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 40 41

Comentarios a estos manuales

Sin comentarios

Wesley PCT-3510-6SA ST Manual de usuario Pagina 14

Comentarios a estos manuales

Relacionado con productos y manuales para Izar Wesley PCT-3510-6SA ST